Hydro power plant monitoring with HBM: Measuring the efficiency of turbine blades
Improve Efficiency of a Water Power Plant and Help to Grow Green Energy
This story tells us how the efficiency of an existing water power plant increased up to 10%, using modern strain-gauge technology and the PMX measuring system. The Iron Gate I (Djerdap Gorge) Hydroelectric Power Station is the largest dam on the Danube River, and one of the largest hydro power plants in Europe. It is located on the Iron Gate gorge, between Romania and Serbia.
The project started in 1964 as a joint-venture between the governments of Romania and Yugoslavia for the construction of a major dam on the Danube River, which would serve both countries. At the time of completion in 1972, it was one of the largest hydroelectric power stations in the world with twelve units generating 2,052 MW, divided equally between the two countries at 1,026 MW each.
Previous mechanization solutions reach their limits
After being in operation for more than 30 years, the revitalization project of six turbines started in Serbia in 2009. The aim was to increase the installed power as well as the efficiency by 10%.
The installed turbines on Đerdap1 are old Kaplan turbines with adjustable blades, and the old design needed change and optimization. The target was to determine, through extensive tests of operational states, where the ratio of produced electricity and consumed water was the largest.
For this purpose, IEENT (The Institute of Nikola Tesla in Belgrade) in cooperation with MFB (The Faculty of Mechanical Sciences, University of Belgrade) and TRC PRO (Technical Research Center) designed a concept of how to measure the efficiency in real-time under working conditions.
To gain the highest effort and increase, the power production of the turbine and the mechanical design of the turbine blades were calculated and designed according to the latest standards.
Reliable sensor technology
The basics of the measurement are strain-gauges, which are applied directly at the turbine wheel input stage. Strain gauges have the advantage of offering a high, long-term stability. This is important in this project because they operate in a virtually endless operation in the plant and it is not efficient to stop the turbine for a recalibration.
- The first strain gauge measurement performed the torque measurement.
- The second strain gauge measurement performed the axial force and speed measurements on the turbine in the input stage.
Strain gages for torque and axial force measurement were positioned on the shaft between turbine wheel and generator (above the turbine wheel and below the generator). They were placed on four axes (view from above: four points equally spaced on the circumference).
For the torque measurement, the engineers decided for the strain gauge type HBM XY41-3/700. Two strain gauge full bridges are working in parallel connection.
For the axial force measurement, the engineers chose the strain gauge type XY31-3/350. Four strain gauge full bridges are working here in parallel connection.
Images of strain gauge installations
After the installation of the strain gauges on the shaft, they were given an electrical protection with a special cover. To prevent the strain gauge measurement in this harsh environment from electromagnetic interferences (EMI), a final cover was put on the measurement areas.
Because the turbine shaft rotates under working condition, the engineers had to find a safe way to transmit the very tiny from the strain gauges to the PMX measurement amplifier system. Additionally, a telemetry system, which sends the measuring signals wireless from the rotating shaft to the receiver, was installed.
Up and running with HBM
The measurement and control system needs to fulfill several tasks, such as fast and reliable measurements, easy set-up, real-time calculations, diagnosis information, no additional software installation, and efficient pricing. These can be archived with the PMX measurement and control system.
In the first step, PMX was used as a four-channel amplifier for voltage inputs. The first input was the voltage from the telemetry system for torque measurements using the strain gages installed on the turbine. The second input was the telemetry system for axial force measurement in the turbine, and the third input was rotational speed. All signals were sampled with 19.2 kHz, which guarantees a high measurement-bandwidth and evaluation of the measurement signals.
All adjustments at the PMX system are handled via the standard Ethernet-interface and the internal PMX webserver. This solution offers the benefit of adjustments being done via the machine network or even remotely, if the additional Wi-Fi is available. So each engineer had a real-time view of the application and the status of the test. An integrated operator prevented unsecure operation.
Powerful real-time calculation with the PMX “Smart Functions”
In the second step, the desired and relevant information had to be calculated in real time. This can be done with the Smart Functions of PMX, which can be used by the operator very easily without having extensive software skills. They offer several mathematical functions, like a pocket calculator, logical functions, and process evaluations up to controller functions like PID-controller.
To calculate the mechanical power, the following formula can be used:
Units: P: W; M: Nm; n: rpm.
Save installation and diagnosis
As an additional protection against dust and EMI, the PMX amplifier was mounted in a cabinet, which includes the supply of the telemetry system also.
The glass in the cabinet allows a direct view onto the PMX and the diagnostic LED-indication. This is an easy and quick indication to determine an eventual error on the device and the measurement status. This is a big advantage for the service engineers, as they can get quick information without using any additional test equipment.
A detailed and deeper diagnostic is stored in the PMX Log-file. This file is stored in the internal memory of the PMX. It covers all upcoming errors of the device and measurement, as well as any changings in the parametrization done by the operators. This allows 100% coverage of the whole test and measurement process.
“A very helpful tool for parametrization, setup and control we found the PMX WebServer. We didn’t need an additional software and could use the standard WebBrowser on our PC’s tablet or smartphone. And it is permanently available in real-time over the whole power-plant area”, says Hotimir Licen from TRC PRO.
Process data-acquisition and evaluation
In the requirements, the engineer-team defined an easy-to-use, robust, and powerful DAQ and evolution software, which has to capture all measurement signals at full speed as well as the calculated channels from the PMX system. These channels are calculated in real time, which means they are calculated with the same speed as the measurement signals. Additionally, the software has to visualize and store all the data and generate a printed report on demand.
All data was captured with HBM’s data-acquisition software catman:
After finishing the project on A4, efficiency tests were performed and new turbine characteristics were determined.
Here are once again the highlilghts of the implemented HBM measurement solution:
- Fast and easy deployment
- Easy setup und helpful diagnosis
- High resolution, accuracy, and speed
- Calculated channels inside the device:
- Dynamic signals and filtered signals
- Torque calculation from strain measurements
- Force calculation from strain measurements
- Power calculation from torque and rotational speed measurement
- Webvisualization application development for data storage without a PC and visualization on a PC, tablet, or smartphone (any device with the web browser).