PACEline CFW 是一種高可靠的感測器,可以在惡劣的工業環境中獲得可靠的測量結果. CFW 儘管尺寸小,但可以提供有效的插拔保護- 這是感測器長期使用的必要條件.

PACEline CFW 壓電力墊圈不僅提供更高的安全性可靠性,其創新性的設計使測試結果的可靠性提高三倍.

  • 更好的線性 于傳統的力墊圈相比 - 由於採用了特殊的帶拼合隔板的測量體
  • 完美的測試結果 即使力沒有完全對中
  • 自動對中 通過其外徑和內徑來完成,並且沒有任何遲滯誤差.

PACEline CFW 現在提供額定量程為 50 kN 140 kN. 其輸出信號不依賴測量範圍,而是依賴應用力, CFW 力感測器有非常高的超載能力。因此, CFW 在多量程範圍內都有很高的精度和測量分度.

CFW 感測器可以於 CMA 電荷放大器一起使用組成 PACEline 壓電力測量鏈:

瞭解 PACEline CMA 放大器詳情

緊湊的壓電力感測器,用於高動態測量

CFW 壓電力墊圈 - HBM PACEline 家族最新成員 - 保證測試和裝配測量的高可靠性. 由於結構緊湊, CFW 力墊圈可以應用于多種應用場合. They can be installed in both the force flow as well as the force shunt.

Accessories and Cables

Accessories

CSB4/1 summing box

Simplify the installation of piezoelectric sensors. The CSB4/1 summing box enables up to four piezoelectric sensors to be connected in parallel to an amplifier input. It can be fastened with screws and features electrical isolation of enclosure and sensor shielding.

CSB4/1 - Data sheet

CSB4/1 - Operating manual

Cables

All cables for piezoelectric transducers from HBM are particularly noise-free and can be used over the sensors' entire temperature range.

The main specifications at a glance:

  • Temperature range: -55 to +200 degrees C
  • Shielding: Semi-conducting intermediate layer, silver-coated copper braid
  • Sheath: FPM
  • Triboelectric noise: Maximum 1 pC
  • Insulation at 20°C: 1014 ohms
  • Impedance: 50 ± 5 ohms
  • Outside diameter: 1.9 mm
  • Bending radius: 10 mm
  • Insulator: PTFE

Our range of accessories is constantly being extended and currently comprises the following cables:

1-CCO

  • Adapter for connecting two cables with 10-32UNF connector
  • Sockets at both ends
  • For extending piezoelectric cables

1-KAB143

  • Cable length: 2, 3 or 7 m
  • 10-32 UNF plug on both sides
  • Suitable for all sensors with plug, CSB summing box and CMA amplifier

1-KAB145

  • Cable length: 0,2 or 3 m
  • 10-32 UNF plug on both sides, however, compared to 1-KAB143 with massive plug protection
  • O-ring seal at sensor for extremely harsh conditions of use
  • Suitable for all sensors with plug, CSB summing box and CMA amplifier

1-KAB176

  • Cable length: 2 or 3 m
  • One side with type 10-32 UNF plug, other cable side with BNC plug
  • For connection of all sensors with plug, CSB summing box and CMD digital charge amplifier

關鍵特性

  • 對稱性設計,高穩定性
  • 額定量程: 50 kN 和 140 kN
  • 高截止頻率
  • 結實的纜線連接器

Mounting aid for Load washer

Piezoelectric load washers require pre-stressing. The new CPS sets of pre-stressing elements facilitate easy and permanent pre-stressing. They are made from stainless steel and offer the required hardness as well as the bolt pitches selected to match the typical pre-stressing force.

A set of pre-stressing elements includes a bolt, a washer and a nut. The figure below gives a schematic representation of the setup.

Related Products

力標定
你想看一眼我們的標定證書嗎? HBM 標定實驗室可以標定的測量量的證書樣例在本頁中下載.
PACEline CMA
PACEline CMA 電荷放大器 (模擬放大器) 可以進行可靠的資料傳輸. 這可以通過信號調理到 +/-10 V 模擬標準放大器.
PACEline CMD
用於壓電感測器的 數位電荷放大器在實驗室和自動化生產過程中都有廣泛的應用. 其容易使用,可靠性高,並且具有優異的性價比
EVIDAS DAQ Software
EVIDAS is HBM's easy-to-use data acquisition and analysis software for fast and straightforward results with an advanced design and clean workflow.
PMX 資料獲取和控制系統
用於現代生產,控制和工業測試台的資料獲取和控制系統。強大的性能,高精度,高可靠,高效率。
馬上獲取報價!

向HBM銷售工程師詢問

請發給我:


開始詢價

向HBM銷售工程師詢問

請發給我:


開始詢價

單獨出價

技術諮詢

快速回應

HBMshop 查看價格、庫存並獲得報價