The kit includes a 15-pin SubHD plug, a metalized plastic housing with knurled screws for fixing the plug at the device, a TEDS chip (1-wire) for storage of a sensor data sheet for automatic channel parameterization, as well as an adhesive label.
Article no.: 1-SUBHD15-MALE
The adapter allows measurements with single strain gauges (SG) in a quarter-bridge circuit and 3-wire configuration.
The adapter completes the connected strain gauge with 3 precise resistors to form a full bridge. The available adapter variants are suitable for 120, 350, 700, or 1000-ohm strain gauges and can be connected to any QuantumX amplifier with a full-bridge input and SubHD socket.
The required parameters such as bridge and gauge factor, bridge excitation, physical unit and calibration data are directly stored on the adapter in the TEDS via software.
The adapter can be used to connect thermocouples with thermo-Mini connectors. The SubHD connector comes with an integrated cold junction (THERMO-MXBOARD).
The available adapter variants are suitable for type K, E, J, or T thermocouples and can be connected to MX840 and MX440 universal amplifiers and their successor models.
The plug-in cold junction can be used for measurements with thermocouples with the MX840 or MX440 universal amplifiers. The board must be installed in the SubHD-15 plug and consists of a cold junction (Pt100) and a 1-wire TEDS chip for transducer identification.
Article no.: 1-THERMO-MXBOARD
The thermo-Mini plug enables a thermocouple to be connected. The plug provides an integrated RFID chip (read/write) which can, for ex., send the measuring point name to the MX1609 amplifier and automatically parameterize the channel (TEDS).
The available plug variants are suitable for type K and T thermocouples and can be connected to MX1609KB or MX1609TB QuantumX amplifiers.
The type K thermocouple is suitable for reliable temperature measurement using the QuantumX MX809B in electrical environments (drives, inverters, cables, batteries).
The thermocouple is spot-welded. It is safe due to a double-insulated and protected 3-m-long cable as well as the insulating cap that protects the Thermo Mini type K from shock and fire. The thermocouple has been certified by VDE according to EN 61010.
Article no.: 1-ITC-K1000
The measuring lead can be used for the reliable measurement of low voltages up to 5V at a high electric potential using the QuantumX MX809B in electrical environments such as batteries.
The lead has free ends. It is safe due to a double-insulated and protected 3-m-long cable as well as the insulating cap that protects the Thermo Mini type copper from shock and fire. The measuring lead has been certified by VDE according to EN 61010.
Article no.: 1-ITC-U1001
This adapter is intended for measurement on an electric drive in 3-phase mode and provides an artificial star point for measuring the phase voltages with QuantumX MX403B or GENESIS.
Connection to the drive by safety lab leads.
Article no.: 1-G068-2
The AC/DC current probe measures based on the Hall effect. It is connected by a 2-m-long cable and a BNC connector. The current probe requires a 9-V block battery. A BNC-to-safety lab socket adapter is included.
Currents that can be measured: 30mA – 30A DC; 30mA – 20A AC eff; DC -100kHz.
Article no.: 1-G912-2
The AC current probe measures inductively. It is connected by a 2-m-long cable with a BNC connector. A BNC-to-safety lab socket adapter is included.
Currents that can be measured: 100mA – 1200A AC eff; 1Hz-100kHz.
Article no.: 1-G913-2
The high-accuracy AC current probe measures inductively. It is connected by a 2-m-long cable with a BNC connector. A BNC-to-safety lab socket adapter is included.
Currents that can be measured: 50mA – 20A AC; 30Hz – 40kHz.
Article no.: 1-G914-2
Powerful software for fast measurement with cloud integration
EVIDAS is HBM’s intuitive software for fast and straightforward results with only 2 clicks.
The advanced design and clean workflow of EVIDAS software provides you with an outstanding visual feedback.
You can choose between four convenient ways to configure your data. Thanks to the cloud integration you can share your data with colleagues around the world.
Article no.: 1-EVIDAS
Software package for easy measurement data acquisition.
The catman Easy main features include convenient channel parameterization using TEDS or the integrated sensor database, measurement job parameterization, individual visualizations, data analysis and event and alarm handling, data storage and export in different formats, e.g. ASCII, Excel, DIAdem, MDF 3/4, or MATLAB.
Installation requires Windows 7/8 or 10. Software maintenance for the first 12 months is included in the package. We recommend an annual renewal.
Article no.: 1-CATMAN-EASY
The catman AP main features include
catman Easy + multi recorder, integration of cameras (Easy VideoCam), online + post-process analysis (EasyMath), automation of recurrent activities (EasyScript), offline preparation of measurement projects (EasyPlan), additional functions like electric power library, special filters, frequency spectrum, etc. Additional data processing and reporting.
Article no.: 1-CATMAN-AP
HBM’s DIAdem driver supports QuantumX, SomatXR, and MGCplus.
DIAdem 10.1 or higher is required. Installation requires Windows 7/8 or 10. Software maintenance for the first 12 months is included in the package.
Article no.: 1-DIADEM-DRIVER
The CANape driver supports QuantumX and SomatXR.
CANape 10.0 or higher is required. Installation requires Windows 7/8 or 10. Software maintenance for the first 12 months is included in the package.
Note: The CAN function of MX471 or MX840 and their successor models is not supported.
Article no.: 1-CANAPE-DRIVER