HBM은 온라인으로 사용자들과 소통하고, 정보를 공유하기 위하여 다양한 웨비나를 준비했습니다.
한국 엔지니어들이 준비한 무료 온라인 교육, 웨비나에 많은 참여바랍니다.
"효율적인 중량 측정을 위한 디지털 로드셀의 장점 "
2020년 8월 11일(화) 오전 10:00-11:00 한국어 강의
기존 아날로그 로드셀과 비교하여 디지털 로드셀의 장점은 무엇일까요?
HBM의 모듈 타입의 디지털 로드셀 제품은 개발자의 중량 측정 관련 개발 시간을 절약하여 고객들의 니즈에 맞추어 효과적인 중량 측정 솔루션 제품을 설계 및 제작 할 수 있습니다.
"BK Connect Impact Test "
2020년 9월 10일(화) 오전 10:00-11:00 한국어 강의
BK Connect Hammer Impact Applet은 임팩트 햄머를 이용한 주파수 응답함수(FRFs) 측정을 보다 쉽게 제공합니다.
측정된 주파수 응답함수 들은 문제 해결을 위한 공진점의 확인과 제품 품질을 향상 시키기 위해 사용 가능합니다.
또한 BK Connect Modal Analysis와 연계하여 모달 파라메터들을 계산할수 있도록 합니다.
"소음 기초 이론 "
2020년 10월 21일(수) 오전 10:00-11:00 한국어 강의
소음에 대한 기본 이론을 살펴봅니다.
- Sound definition : Terminology of Sound, Sound pressure vs Sound power
- dB Conversion : Range of Sound pressure level, Perception of dBs, Simple rules for conversion
- Sound Fields
- dB : Sound source, dB levels & value
"소음 측정 기초 이론 "
2020년 10월 22일(목) 오전 10:00-11:00 한국어 강의
소음 측정에 대한 기본 이론을 살펴봅니다.
- Sound measurement consist : Microphone
- Sound level meter : Time weighting
- Equivalent Level
"소음 주파수 분석 기초 이론 "
2020년 10월 23일(금) 오전 10:00-11:00 한국어 강의
소음 주파수 분석에 대한 기본 이론을 살펴봅니다.
- Frequency : Frequency range, audible range
- Frequency analysis : Filter types and frequency scales, 1/1 and 1/3 octaves filters
- Perception of Sound : Auditory field , Equal loudness contours for pure tones, perception of noise, frequency weighting curves
Optimize Key Parameters by Adding Sensor Data
Tuesday, September 1, 2020 03:00 PM CET | 08:00 AM CT | 09:00 AM ET online
In this webinar you will learn how to easily fine-tune and maintain algorithms running on Electronic Contrul Units (ECU). Additional sensor data, integrated via xCP interface, helps to understand the overall physics and to optimize software functionality.
Challenges of Structural Health Monitoring (SHM)
Wednesday, September 2, 2020 04:00 PM CET | 09:00 AM CT | 10:00 AM ET online
Tuesday, September 08, 2020 11:00 AM CET online
Join this webinar for a thorough introduction to our brand-new data analysis software, BK Connect.
With modern and efficient work processes, getting the job done is easy. This session provides attendees with an overview of BK Connect and an understanding of the general scope of time data post-processing. Learn how to build your own analyzer process chain and how to link several chains into a working process.
ADVANCED 2250 AND 2270 SOUND LEVEL METER
Tuesday, September 22, 2020 11:00 AM CET online
Join this open forum for Type 2250 and 2270 owners to learn how to get the best from your sound level meter. Subjects covered include establishing multiple users/templates and using data in other software.
B&K 2245 SOUND LEVEL METER INTRODUCTION
Tuesday, October 06, 2020 11:00 AM CET online
B&K 2245 is the latest in our range of iconic sound level meters providing a complete solution for basic noise measurements, while combining functionality, ease-of-use and versatility with the reliability and confidence that is ensured with the Brüel & Kjær brand.
Join this webinar to learn more!
Maintenance Optimization and Production Improvement with
Tuesday, August 11, 2020 1PM - 4PM EST online
During this three-hour online session, attendees will learn how to increase system productivity, discover industry best practices and strategies for reducing the total life cycle cost. Attendees will see how ReliaSoft software can be used to conduct RAM analysis to optimize maintenance and production.
Design for Reliability Webinar Series: Part 2 - Reliabili
Thursday, August 18, 2020 1:30 AM ET/11:00 AM IST/7:30 AM CET online
Failure Mode and Effect Analysis (FMEA) is a very well known method used to discovering potential failures that may exist within the design of a product or process. Using Design FMEA (DFMEA), you can generate necessary information to quantify the reliability and use that as a baseline indicator to check whether it meets the Reliability Target. This webinar will discuss the process of translation such information from DFMEA to a Quantified Reliability Estimate using ReliaSoft XFMEA software.
Design for Reliability Webinar Series: Part 3 - Reliabili
Thursday,September 17, 2020 5:30 AM ET/3:00 PM IST/11:30 AM CET online
Time to market is a critical factor in any product’s success. With today’s high reliability requirements and short development cycles, testing for the full product life is expensive and impractical. By testing at elevated stress levels, the reliability of a component can be quantified in a shorter period of time, while saving money and resources. This process is called quantitative accelerated life testing (QALT) and employs several statistical and practical techniques to characterize product behaviour. During this webinar, we will introduce the theory and principles of QALT and life testing using Accelerated Lifes Testing module available in ReliaSoft Weibull++ software.
Design for Reliability Webinar Series: Part 4 - Reliabili
Monday, October 26, 2020 1:30 AM ET/11:00 AM IST/7:30 AM CET online
During this webinar, attendees get familiar with will the principles of reliability growth testing and strategies using ReliaSoft Weibull++ software.
Design for Reliability Webinar Series: Part 5 - Reliabili
Wednesday, November 11, 2020 5:30 AM ET/3:00 PM IST/11:30 AM CET online
Reliability and durability fit together in product validation testing. Often, the product’s life requirement is being able to withstand loading over a specified duration with defined reliability and confidence requirements: "The part must be free of visible cracks with a reliability greater than 90% with a 90% lower 1-sided confidence bound after being subjected to loading representative of 4,000 service hours." Durability, life data and reliability analyses can help engineers answer critical questions whether how long to test and how many parts to test in order to meet these life requirements. In this webinar, we will discuss the important link between testing to prove durability and testing to demonstrate reliability.
선택됨: 필터 없음
총 217 개의 결과가 검색되었습니다.